< Back to Results

ZEUS Training Module 06

Applies To: ZEUS
Overview:

Scanner Data Graphing View: View Selection, Properties, PID Triggers, Trigger Points, Zoom, Save

Resolution:

VIDEO TRANSCRIPTION

Welcome to Snap-on Training Solutions. This module is designed to help you get the most out of your diagnostic tool, and covers the use of scanner data in graphing view.

Monitoring data parameters from the vehicle electronic control module, or ECM, is extremely helpful when tracking down vehicle faults.

A numeric view of Parameter ID, or PID data, will not always reveal problems or show relationships between PIDs. Graphing relationships between data parameters gives you a view of performance over time and enables you to compare multiple data parameters.

Data graphing can show momentary failures, and data trends over time.

View Selection

Select the expand/collapse icon to open the data graph for the parameter. The graph provides a large number of data points plotted so that you can compare events over time.

The tool continuously records data for all available parameters. From one to sixteen graphs can be displayed, allowing you to view relationships between components.

The Min and Max values show the current, maximum and minimum data values. These values are stored even after the data has scrolled off the screen.

Select the PID menu icon to display the PID menu, then select full screen graph to view the PID in full screen.

Use the menu icon again to select normal graph to return to the standard view.

Properties

Selecting the Properties button allows you customize the colors, settings, and sweep of the graph display.

PID triggers

Using a PID Trigger allows you to capture data that is outside of normal range, by setting upper and lower values to start recording data when the signal crosses them.

To set up the trigger, select the PID menu icon, then select Setup. From the Graph Properties dialog box, select Trigger On.
 
A checkmark appears, and the Min and Max fields activate. Enter the desired trigger value into each field.  

A reminder about making sure to arm the trigger is also displayed. We’ll get to arming the trigger in a minute. 

Select Save to close the dialog box. 

Trigger Points

Dashed Red trigger lines now display on the selected graph. The area between the upper and lower trigger lines establishes the triggering condition. Data points that fall outside of these limits will trigger the recording.

Notice the flashing Snapshot icon. This indicates that the trigger is not armed.

Select the Snapshot icon to arm the trigger. Notice that is stopped flashing. This lets you know the trigger is  armed and ready to record.

Remember that the Snapshot icon arms and disarms all PIDs with triggers. So if you set more than one trigger, this will turn them all on or off at the same time.

In our example, the upper limit was exceeded and activated the trigger. When the trigger was activated, a data snapshot or movie was captured and a message displayed.

Notice the red flag, red PID text, and red marker showing where the value was exceeded. These make it easier to see in the PID list.

Zoom

The zoom option allows you to change the magnification level of the sweep. 

Select the Plus button to zoom in and increase magnification; select the Minus button to zoom out and decrease magnification.

Save

The Save Icon saves the current screen information, along with all data stored in the buffer.

The recorded data movie is automatically saved. 

Select the Data Manager icon on the home screen.

Select Scanner Data Folder.

Choose the data movie you want to see.

Use the green arrow icon to play the entire movie, or use the scroll buttons to scroll forward and back through the collected data. 

Scroll down to view more data parameters.

Snap-on is dedicated to helping you get the most out of your diagnostic tool and keep your customers happy. Be sure to watch the rest of the modules in this Training Solutions series.

Last Updated: October 1, 2019
 

Got Questions?

 

Contact our Customer Care Department:

Email: techsales.uk@snapon.com

Tel: (01553) 692422

Mon-Fri 8.45am-5pm

 

For Snap-on Tools or to contact your local dealer, call (01536) 413800

E-mail kettcustserv@snapon.com

 

Software Subscription enquiries:

(01536) 413825 and choose option one

E-mail kettsubscriptions@snapon.com

Mon-Fri 8.30am-5pm

Snap-on

Snap-on is a trademark of Snap-on Incorporated.

All other marks are trademarks of their respective holders.

© 2019 Snap-on Incorporated. All Rights Reserved.

Got Questions?

Contact our Customer Care Department

Email: techsales.uk@snapon.com

Tel: (01553) 692422

 

For Snap-on Tools

or to contact your local dealer

call (01536) 413800

E-mail kettcustserv@snapon.com

We welcome your feedback on our website.

 

Enter your name:

email:

 

Please rate your experience in the following:
(1 being an unpleasant experience and 10 being exceptional)

Navigation

 1  2  3  4  5  6  7  8  9  10

Content

 1  2  3  4  5  6  7  8  9  10

 

Suggested improvements:


Can we contact you by e-mail to discuss your feedack further?

Yes

If you would like to receive e-mails from Snap-on about product releases, developments and promotions, please click the box below.

Yes - I would like to receive further e-mails from Snap-on about product releases, developments and promotions

We have placed cookies on your computer to give you the best possible experience with our website. These cookies are also used to ensure we show you advertising that is relevant to you. If you continue without changing your settings, you are agreeing to our use of cookies to improve your user experience. You can click the cookie settings link on our website to change your cookie settings at any time.
Privacy Policy