< Back to Results

ETHOS PRO Training Module 6

Applies To: ETHOS® PRO
Overview:

Global OBD-II, The Ten Modes of OBD-II

Resolution:

Video Transcription

Snap-on Training Solutions helps you get the most out of your ETHOS PRO diagnostic tool. This training module covers the use of Global OBD-II scanner functions.

Global OBD-II scanner coverage is strictly related to emissions related coverage and is universal in that all vehicles sold in the US and Canada since 1996 must comply with this standard. All 10 modes of OBD-II are covered by this tool and our accessed by selecting the OBD-II icon on the home screen. All service modes are not supported by all vehicles, so the available menu selections will vary. Note: some vehicles do not support all 10 modes, so results will vary.

Let's start by exploring the OBD direct functions. This opens a menu of two choices, OBD diagnose and OBD training mode. Training mode allows you to navigate through the menus and see results without being connected to a vehicle. This is a good way to explore OBD-II capabilities.

For this demonstration, we will select OBD diagnose to diagnose a vehicle. Start communication initiates the test session. Manual protocol selection establishes which vehicle protocol to use. Let's select connector information to see where we can find the data link connector or DLC on the vehicle. Let's choose an Alfa Romeo. Some of these models may not be familiar in the US but all vehicles are included in the Global OBD-II. So you always know you have emissions coverage on any vehicle. Let's select model 147. Here's the connector location. Have you ever searched for a connector that was not in the usual place? the DLC locator makes it easy. Now select continue.

Readiness Monitors

Coverage includes all 10 modes of OBD-II and readiness monitors. Which are very important when verifying emission repairs. Readiness monitors provide a status report on emissions related systems. Some monitor reports require an extensive drive cycle in order to complete the requirements of the test. Results are shown for each monitor, whether the monitor is supported by the vehicle and whether the drive cycle test is complete for each monitor. Monitor tests must be complete in order for the vehicle to be ready for an emission test.

Ten Modes of Global OBD-II

Let's take a brief look at the valuable information inside each of the 10 modes of OBD-II. Mode one displays live data parameters for the engine and emissions systems. This is typically your first step when diagnosing a check engine light.

Mode two displays freeze frame data. This is a record of vehicle data parameters captured at the moment of fault code was set. This can give valuable insight into the operating conditions of the vehicle at the time of the fault.

Mode three displays the OBD-II trouble codes currently set by the vehicle. OBD-II fault codes are standard for every vehicle manufacturer. The code definition is also shown on the right to explain the meaning of the code.

Mode four provides an easy method to turn off the malfunction indicator lamp or MIL after a repair. Caution: this also clears freeze frame data, pending codes and readiness monitors. So this should usually be the last step in your repair process.

Modes five, six, and seven display data parameters related to oxygen sensors, saved results of manufacturer specific tests and trouble codes detected during the last drive cycle. This is useful in determining the root cause of recurring fault codes.

Mode eight allows a service technician to invoke an onboard test, to seal the evaporative system for a pressure test. This function varies by manufacturer. For example, on Ford systems, this closes the canister vent solenoid for 10 minutes.

Mode nine can read the vehicle identification number or VIN as well as the calibration and ID numbers for the engine control unit or ECU. Mode nine performance tracking displays a record of the number of times each of the readiness monitors have been completed.

Mode 10 displays, diagnostic trouble codes with permanent status. These codes are stored in the powertrain control module for 400 days and cannot be cleared. Remember for easy navigation, you can use the back icon at anytime to step back one screen, and the home icon is a shortcut to the main menu.

Snap-on is dedicated to helping you get the most out of your diagnostic tool and keep your customers happy. Be sure to watch the rest of the modules in this Training Solutions series.

Last Updated: August 20, 2020
 

Got Questions?

Contact Diagnostic Customer Care:
 
Car & Light Truck Diagnostics

Send e-mail
(800) 424-7226

 
Heavy-Duty Truck Diagnostics

Send e-mail
Contact us here
(800) 311-5452

 
Request Product Information

Snap-on Diagnostic Tools and

Repair Information

Snap-on is a trademark of Snap-on Incorporated.

All other marks are marks of their respective holders.

©2020 Snap-on Incorporated. All Rights Reserved.

Got Questions?

Request Product Information

Online Product Help Here

Contact Diagnostic Customer Care

Send e-mail

(800) 424-7226

Mon - Fri 6am - 5pm PST

 

Product Registration:

• US     • Canada

We welcome your feedback on our website.

 

Enter your name:

E-mail:

 

Please rate your experience in the following:
(1 being an unpleasant experience and 10 being exceptional)

Navigation

 1  2  3  4  5  6  7  8  9  10

Content

 1  2  3  4  5  6  7  8  9  10

 

Suggested improvements:


Can we contact you by e-mail to discuss your feedack further?

Yes

If you would like to receive e-mails from Snap-on about product releases, developments and promotions, please click the box below.

Yes