< Back to Results

TRITON-D8 Training Module 1

Applies To: TRITON-D8®
Overview:

Introduction and Navigation

Resolution:

VIDEO TRANSCRIPTION

Welcome to Snap-on Training Solutions®. This module is designed to help you get the most out of your TRITON-D8™ diagnostic tool, and covers the controls and basic setup functions.

Before operating or maintaining TRITON-D8 read the safety instructions and user manual carefully, paying extra attention to the safety warnings and precautions.

Getting Started

To install the battery pack, loosen the two screws that retain the battery compartment cover. Lift the bottom edge of the cover to remove. Put the notched end of the battery in first and push down until the battery is in place. Replace the battery cover and snug up the screws to hold the cover in place. Do not over-tighten. Indicators and connectors are on the top panel. The power indicator illuminates when power is being supplied to the tool. A red light indicates the battery is charging. A green light means the battery is fully charged, an amber light means there's an issue with the battery. The power supply port is used to connect the AC/DC power supply. Use only the correct AC adapter provided with the TRITON-D8. The Mini USB port is used to connect TRITON-D8 to a personal computer for transferring saved files. The Micro SD card port holds the micro SD card that contains the TRITON-D8 software and the data cable port is for the scanner vehicle connector.

Buttons

Pressing the yes button, selects a menu or program or confirms a selection. Pressing the no button exits a menu or returns to the previous screen. The four way keypad controls up, down and left and right navigation. The shortcut s button can be programmed to perform a variety of common tasks. To power up the TRITON-D8, press the power button. TRITON-D8 automatically powers up and opens to the home screen whenever it is connected to a vehicle or the AC power adapter. TRITON-D8 will boot up to the home screen in about five seconds. All operations of TRITON-D8 can be performed using the touch screen or the keys.

Icons

Our home screen contains seven icons. Let's do a brief overview of the icons. The scanner icon is your access to VIN code specific diagnostics. The OBD-II/EOBD icon provides access to the emissions-related information covered under SAE J1979 standard. Guided Component Tests accesses Snap-on's exclusive Fast-Track® Guided Component Tests including a variety of resources to test automotive components for a confident diagnosis. This avoids replacing the wrong part and the risk of comebacks. The Scope Multimeter function allows you to perform multiple types of circuit and component measurement tests. The Quick Lookups icon contains oil specs and resets allowing you quick access to the following OEM information. The Previous Vehicles and Data icon is the shortcut to any vehicle previously connected or saved data. The Tools icon allows access to set up the tool; everything from Wi-Fi set up, Snap-on cloud, altusdrive.com or connect to a PC.

Setup

From your home screen, follow along to properly set up your diagnostic platform. Press the Tools icon, press settings to enter the settings menu. System settings allows you to set display, date and time and auto VIN.

The display menu allows you to change the screen settings. Brightness allows you to change how bright the screen is. This can be useful when using the tool in bright sunlight. Color theme allows you to change from a day theme to a night theme. High contrast toolbar allows you to change from a color toolbar to a high contrast toolbar. Font type allows you to change from a normal font to a bold font. Backlight time allows you to change how long the screen stays at full brightness before dimming. This applies only when the tool is on battery power and can extend the time the tool can be used before needing to be recharged. Touch calibration will walk you through the screen calibration.

The date and time menu allows you to change the time zone, time and date format and more. The Auto VIN menu allows you to turn the Instant ID feature on or off. Instant ID is a built-in scanner feature that will save you time when identifying a vehicle by automatically communicating with the vehicle's ECM to complete the vehicle identification process automatically.

Configure Wi-Fi functions to turn on and connects to wireless Internet. If the screen displays a message, Wi-Fi is Off, select the Wi-Fi power icon to turn the Wi-Fi on. The Wi-Fi power icon will change from a Checkmark icon to an X icon indicating Wi-Fi radio is currently set to on. Select your desired network connection. If the network is password protected, a keyboard will appear, simply enter your network password. If your network does not require a password, select it. Select Connect to connect to your desired network. From the connect confirmation screens, select OK to continue using this connection or Forget to disconnect this connection.

The configure scanner menu gives options for showing the graph scales or hiding the graph scales in data graphing mode.

The Configure Units menu allows you to change between metric and imperial units.

System Information displays important information that may be needed from time to time. If you call Customer Support, they may ask for certain information displayed here, such as the tool's serial number, the installed software version number and other system information like installed database and hardware codes. Normally you may never need to use this information but it is easily accessed here if you need it.

Configure shortcut key allows you to set up what the S button on the front of the tool does when pressed. Choices for the Shortcut Key function include screen brightness, saved screen, saved movie, show shortcut menu and toggle record and pause. Many top shops use capturing screenshots as a great method for showing the owner of the vehicle either an image of a failure, or suspected failure, that would require additional testing.

ALTUS set up displays the serial number, pin and code that are needed to link your tool to the Snap-on Cloud at alltusdrive.com. For more information on the Snap-on Cloud, please see the Snap-on Cloud training module in this series.

Connect-to-PC allows you to connect the tool to your own PC using the supplied USB cable. You can then use the free ShopStream Connect™ software to view and print any saved files on the tool. The software is available at this website, diagnostics.snapon.com/ssc. ShopStream Connect can be used to view and print vehicle system reports, screenshots and recorded data. It can also be used to update your scan tool over the internet. Speak to your Snap-on Representative to learn more about online updates.

Snap-on is dedicated to helping you get the most out of your diagnostic tool and keep your customers happy. Be sure to watch the rest of the modules in this Training Solutions series.

Last Updated: August 20, 2019

Snap-on Diagnostic Tools and

Repair Information

Snap-on is a trademark of Snap-on Incorporated.

All other marks are marks of their respective holders.

©2019 Snap-on Incorporated. All Rights Reserved.

Got Questions?

Request Product Information

Online Product Help Here

Contact Diagnostic Customer Care

Send e-mail

(800) 424-7226

Mon - Fri 6am - 5pm PST

 

Product Registration:

• US     • Canada

We welcome your feedback on our website.

 

Enter your name:

email:

 

Please rate your experience in the following:
(1 being an unpleasant experience and 10 being exceptional)

Navigation

 1  2  3  4  5  6  7  8  9  10

Content

 1  2  3  4  5  6  7  8  9  10

 

Suggested improvements:


Can we contact you by e-mail to discuss your feedack further?

Yes

If you would like to receive e-mails from Snap-on about product releases, developments and promotions, please click the box below.

Yes - I would like to receive further e-mails from Snap-on about product releases, developments and promotions