< Back to Results

VERUS Edge Training Module 1

Applies To: VERUS® Edge
Overview:

Introduction and Controls

Resolution:

VIDEO TRANSCRIPTION

Welcome to Snap-on Training Solutions. This module is designed to help you get the most out of your VERUS Edge diagnostic tool, and covers the basic setup and controls. 

Getting Started

Before operating, read and understand the safety warnings within the Important Safety Instructions manual and User Manual.

Controls

Press the power button to get started. The unit turns on and automatically launches the diagnostic software suite.

The power button also functions as a power status indicator. Red means the battery needs charging. Blinking red means the tool is in Ready Mode. Orange means the battery is charging. Green indicates the battery is charged. 

The power button also indicates when the diagnostic tool is in sleep mode. To enter Sleep Mode, just press and release the power button. To restart, simply press the power button to continue operation.

A capacitive touchscreen provides precise menu control and multi-touch gesture capabilities. 

The “S” Shortcut button can be setup to perform routine functions, like capturing a screen shot, taking a photo, or opening the onscreen keyboard. To configure the “S” button: 

Press the “S” button.

Select the Settings icon from the slide-out menu. 

Choose the function you would like the “S” button to perform.  The active setting is indicated within a yellow highlighted box. 

A stylus is stored in the built-in holder. The Battery Pack, Collapsible Stand, Removable Scope Multimeter Module and Camera Lens are also located on the back. 

Lithium-Ion Battery Pack

A Lithium-ion battery pack is used, providing approximately 5 hours of operation and days of standby power in Ready Mode.

To replace the battery pack, open the stand.

Loosen the two battery pack screws, then carefully pull out on the bottom edge of the battery pack and lift it out.

The battery pack is installed in the opposite manner. Be sure to only snug up the screws and don’t over tighten.

Connections

External device connection points are located on the left side under the hinged cover in the hand grip.

Two USB jacks are provided, a standard 2.0 and a dual mode 2.0, 3.0. These allow connection to a printer, keyboard, mouse or other devices.

A Micro uSD card slot is provided for extra memory storage. The power supply and headphone jacks are also located under the cover.

To avoid damage, use only the AC/DC power supply that came with the diagnostic tool.

Scope Multimeter Module

The Scope Multimeter Module allows you to perform electrical circuit tests and monitor signals. 

The Module docks into the diagnostic tool and is secured with a lock tab. To undock depress the lock tab and slide the module up to remove it. 

With the module undocked, it can now be used remotely. Simply connect the supplied USB cable to the diagnostic tool and then to the USB jack on the bottom of the module. 

The module is equipped with multiple Scope Multimeter jacks, for testing up to four signals at once, and an Auxiliary (DB9) Connector for connecting the optional RPM inductive pickup.

Scan Module

The Scan Module connects to the vehicle data link connector or DLC and then wirelessly transmits vehicle data to the diagnostic tool. The Scan Module must be paired with the diagnostic tool in order to communicate. If the wireless signal is lost, an audible alarm will sound and a warning message is displayed. The signal will automatically restore itself when the devices are brought within operating range of each other. 

This module contains the following connections and indicators: Data cable connector, green Bluetooth LED, red Communication issue LED and green Vehicle power LED. The memory card and USB ports can be accessed by removing the protective hand grip.

Last Updated: June 13, 2019

Snap-on Diagnostic Tools and

Repair Information

Snap-on is a trademark of Snap-on Incorporated.

All other marks are marks of their respective holders.

©2019 Snap-on Incorporated. All Rights Reserved.

Got Questions?

Request Product Information

Online Product Help Here

Contact Diagnostic Customer Care

Send e-mail

(800) 424-7226

Mon - Fri 6am - 5pm PST

 

Product Registration:

• US     • Canada

We welcome your feedback on our website.

 

Enter your name:

email:

 

Please rate your experience in the following:
(1 being an unpleasant experience and 10 being exceptional)

Navigation

 1  2  3  4  5  6  7  8  9  10

Content

 1  2  3  4  5  6  7  8  9  10

 

Suggested improvements:


Can we contact you by e-mail to discuss your feedack further?

Yes

If you would like to receive e-mails from Snap-on about product releases, developments and promotions, please click the box below.

Yes - I would like to receive further e-mails from Snap-on about product releases, developments and promotions

We have placed cookies on your computer to give you the best possible experience with our website. These cookies are also used to ensure we show you advertising that is relevant to you. If you continue without changing your settings, you are agreeing to our use of cookies to improve your user experience. You can click the cookie settings link on our website to change your cookie settings at any time.
Privacy Policy