< Back to Results

VERUS PRO Training Module 1

Applies To: VERUS® PRO
Overview:

Introduction and Controls

Resolution:

VIDEO TRANSCRIPT

Snap-on Training Solutions helps you get the most out of your VERUS® PRO diagnostic tool. This training module covers the basic setup and controls.

GETTING STARTED

IMPORTANT: Before operating or maintaining VERUS PRO, read the safety instructions and user manual carefully paying extra attention to the safety warnings and precautions

Button Controls

To power up the VERUS PRO, press the power button. VERUS PRO powers up and automatically opens the diagnostic software.

VERUS PRO has a touchscreen display that can be used for most operations.

The power indicator light shows red when the tool needs charging and green when charged

There is a microphone

A hard drive activity LED

The “S” button will take a screenshot when pressed

The four-way key pad contains up-down, left-right, and an enter button

There is a button for the camera, one to bring up the virtual keyboard and one to change the screen brightness

The audio speaker is at the bottom left

VERUS PRO back view

The back side of the unit includes: a socket for a security lock - not included, the Battery Compartment Cover, Collapsible Stand and the Camera Lens

Rechargeable Lithium-Ion Battery Pack

Approximate 3 hour run time. Approximate 5 hour charge time with AC power supply.

To replace the battery pack, move the stand to the open position, loosen the two screws that hold the battery in place, then pull on the top edge of the battery and lift.

Then place the bottom of the new battery into the front edge of the compartment and push the top of the battery down into the compartment to lock into place.

Snug up the screws to hold the battery in place. Do not over tighten.

CONNECTIONS

Connections are on the left side of the VERUS PRO under a hinged cover.

The 2 USB Client Ports are used to connect VERUS PRO to external devices, such as a printer or USB keyboard.

There are headphone and microphone jacks and a power supply port. Use only the AC adapter provided with the VERUS PRO.

SCOPE MULTIMETER MODULE

The Scope Multimeter Module installs into the Display Device and is held in place by a lock tab. Depress the lock tab and the Scope Multimeter Module is easily removed from the Display Device. A USB cable (supplied with your kit) can then be used to connect the Scope Multimeter Module to the Display Device. Now you can continue to remotely monitor circuit activity while moving the Display Device around the vehicle.

The Scope Multimeter Module contains the following ports and connection points: Common or Ground Port, Ports for Channels 1 through 4, a 9-pin Auxiliary Port and a USB Port (under a protective cover)

SCAN MODULE

The Scan Module is a wireless communications device that transmits vehicle data to the display without a physical connection. If the module is out of range and the wireless signal is lost, it sounds a tone and the Display shows a warning message. The signal automatically restores itself when the unit is brought back in range.

The Scan Module contains the following Connections and Indicators: Data cable connector, green Bluetooth LED, red Communication issue LED and green Vehicle power LED. The memory card and USB ports can be accessed by removing the protective hand grip.

Last Updated: July 31, 2019

Snap-on Diagnostic Tools and

Repair Information

Snap-on is a trademark of Snap-on Incorporated.

All other marks are marks of their respective holders.

©2019 Snap-on Incorporated. All Rights Reserved.

Got Questions?

Request Product Information

Online Product Help Here

Contact Diagnostic Customer Care

Send e-mail

(800) 424-7226

Mon - Fri 6am - 5pm PST

 

Product Registration:

• US     • Canada

We welcome your feedback on our website.

 

Enter your name:

email:

 

Please rate your experience in the following:
(1 being an unpleasant experience and 10 being exceptional)

Navigation

 1  2  3  4  5  6  7  8  9  10

Content

 1  2  3  4  5  6  7  8  9  10

 

Suggested improvements:


Can we contact you by e-mail to discuss your feedack further?

Yes

If you would like to receive e-mails from Snap-on about product releases, developments and promotions, please click the box below.

Yes - I would like to receive further e-mails from Snap-on about product releases, developments and promotions