< Back to Results

Pairing the Scan Module via Bluetooth

Applies To: VERUS™ Edge, ZEUS

To use the Scan Module with the Scanner or OBD-II/EOBD functions, it must first be paired with the diagnostic tool.


Pairing is the wireless connection (identification) process used to connect the Scan Module to your diagnostic tool. The Scan Module only needs to be paired once before it’s initial use. The connection configuration should remain in memory for all future uses, unless the connection configuration is removed or lost.

NOTE: Wireless devices shown in this section are used as reference. Not all devices shown may be applicable to your diagnostic tool.


IMPORTANT: The Scan Module needs to be powered on during the pairing process. Connect the Scan Module to a vehicle or to the diagnostic tool using the USB cable. Make sure the diagnostic tool has a charged battery or is connected to the AC/DC power supply.

To pair the Scan Module with the diagnostic tool:

  1. Turn on the diagnostic tool.
  2. Connect the 26-pin end of the data cable to the Scan Module data cable connector.
  3. Connect the 16-pin end of the data cable to a vehicle data link connector (DLC). The green LED on the Scan Module is illuminated when power is being supplied to the Scan Module.
  4. From the diagnostic tool select System Settings > Paired Devices.
  5. Select Add from the toolbar, then OK when prompted. The diagnostic tool searches for compatible wireless devices, then displays the results. 
    NOTE: i Search results include all compatible wireless devices detected, and may include multiple Scan Modules if you are in a shop environment where more than one unit is powered on. Available module listings include a partial serial number. Make sure the screen listing matches the last six digits of the serial number of your Scan Module before continuing.
  6. Select the Scan Module you wish to connect from the results list. A search in progress message displays during the pairing procedure, the Paired Devices screen displays once the procedure completes.
  7. Select the Home icon on the Toolbar.
  8. Disconnect the data cable from the vehicle.

The Scan Module and diagnostic tool are now paired for wireless communication and should automatically recognize each other when both are powered up.

Last Updated: October 1, 2019

Got Questions?


Contact our Customer Care Department:

Email: techsales.uk@snapon.com

Tel: (01553) 692422

Mon-Fri 8.45am-5pm


For Snap-on Tools or to contact your local dealer, call (01536) 413800

E-mail kettcustserv@snapon.com


Software Subscription enquiries:

(01536) 413825 and choose option one

E-mail kettsubscriptions@snapon.com

Mon-Fri 8.30am-5pm


Snap-on is a trademark of Snap-on Incorporated.

All other marks are trademarks of their respective holders.

© 2019 Snap-on Incorporated. All Rights Reserved.

Got Questions?

Contact our Customer Care Department

Email: techsales.uk@snapon.com

Tel: (01553) 692422


For Snap-on Tools

or to contact your local dealer

call (01536) 413800

E-mail kettcustserv@snapon.com

We welcome your feedback on our website.


Enter your name:



Please rate your experience in the following:
(1 being an unpleasant experience and 10 being exceptional)


 1  2  3  4  5  6  7  8  9  10


 1  2  3  4  5  6  7  8  9  10


Suggested improvements:

Can we contact you by e-mail to discuss your feedack further?


If you would like to receive e-mails from Snap-on about product releases, developments and promotions, please click the box below.

Yes - I would like to receive further e-mails from Snap-on about product releases, developments and promotions

We have placed cookies on your computer to give you the best possible experience with our website. These cookies are also used to ensure we show you advertising that is relevant to you. If you continue without changing your settings, you are agreeing to our use of cookies to improve your user experience. You can click the cookie settings link on our website to change your cookie settings at any time.
Privacy Policy